CircuitValley : Embedded Engineering

Cutting edge Embedded Technology made understandable, accessible.

Search This Blog

Blog
Shop
About
RFGEN44 on CrowdSupply
CHC5 Open Camera Kickstarter

Showing posts with the label ADF4351

View all

Posts

RFSTAMP44 RF Signal Generator ADF4351 35M to 4.4Ghz Stamp size castellated

September 15, 2025

Get link
Facebook
X
Pinterest
Email
Other Apps

RFGEN44 Open Source 4.4Ghz USB RF Signal Generator

August 08, 2025

ADF4351 RF RF Signal Generator USB Interface

Get link
Facebook
X
Pinterest
Email
Other Apps

Gaurav Singh: I am an Avionics Engineer, with knowledge of Electronics, Software, FPGA and Embedded Design Engineering.

Visit profile

Subscribe To Embedded Engineering Blog

Posts

Atom

Posts

All Comments

Atom

All Comments

Pickit 2 clone The Universal Microchip PIC Programmer /Debugger

About The programmer The PICkit™ 2 Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash families of microcontrollers. The full featured Windows programming interface supports baseline, mid-range, PIC18,8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip’s powerful MPLAB Integrated Development Environment (IDE) the PICkit 2 enables in circuit debugging on most PIC microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified. Features 1. This device will work like the normal pickit2. 2. This wll work for any pic (5 and 3.3V devices) 3. No mosfets no complex, only one voltage boost circuit. 4. you can program the target without PC. ...

USB 8051 (89 series) & AVR Microcontroller Programmer

About the programmer This simple microcontroller programmer can progam most of the 89 like Atmel's AT89S51, AT89S52, AT89S53, AT89S8252, AT89S8253 including the Atmel AVR series of microcontroller , it does not support 89C series . It simply consists of an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver, no special USB controller is needed. Features Works under multiple platforms. Linux, Mac OS X and Windows are tested. No special controllers or smd components are needed. Programming speed is up to 5kBytes/sec. SCK option to support targets with low clock speed (< 1,5MHz). if you have all ready have your USBasp programmer, which is previously posted on my blog as USB AVR PROGRAMMER then there is no need build new hardware you just need to change the firmware of the programmer microcontroller. Simple Steps to made This programmer Step ...

IR(infrared) Remote Control Relay Board with PIC 12F675 Microcontroller

Introduction This little project will demonstrate how you can use your old NEC IR protocol based TV,DVD or VCR remote control to control you home appliances like fan bulb or virtually anything. Consumer IR protocols There are a number of consumer Infrared protocols out there and they have been used for every single purpose possible i guess, like PDA laptops and other consumer appliances. RC-5 & RC-6 by Phillips , RCA are few examples of consumer IR protocols. In this demonstration we will stick the to NEC protocol by NEC corporation, NEC Protocol Based Remote Control for this Bord Remote Control for This Board NEC Infrared Protocol

AVR Serial Port Programmer

About AVR Programmer This simple COM PORT based AVR atmega Programmer will allow you to painlessly transfer hex programs to most ATMEL AVR microcontrollers without sacrificing your budget and time. It is more reliable than most other simple AVR programmers available out there and can be built in very short amount of time. AVR programmer consists of in-circuit serial programmer (dongle) and small pcb with a DIP socket where you can fit your microcontroller and have it quickly programmed. You may also use this programmer as a stand alone in-circuit serial programmer that can be used to conveniently program AVR microcontrollers without removing them from the target circuit. Entire AVR programmer has been build with using common parts and fits in the case of the serial connector. The socket pcb has been created to fit a 28-DIP AVR ATmega8 microcontroller, but you can build a socket pcb for any other AVR microcontroller out there. This AVR progra...

Labels

30ps1 53131A 53132A Counter2 ADF43512 ADR13993 ADR1399KHZ2 Altera2 AMD Zynq2 Aritikel auf Deutsch1 ARM6 Atmel 80511

Atmel AVR4 Breakout3 Camera3 COM Port Programmer2 Cypress FX36 Distribution Amplifier1 DSP2 E-ink Display2 fast pulse1 Fast Pulse Generator1 Fast Rising edge1 Fast Rising Edge Generator1 FMC5 FMC HPC1 FMC LPC3 FPGA20 FPGA Basics7 FPGADrive1 GPSDO OCXO3 HPC1 I2S Audio1 Ikea5 IR Remote Control3 Keysight2 Lattice3 LCD Graphics and Alphanumeric15 LED4 LED Driver2 Leo Bodnar fast pulse1 Lighting1 Linux7 LM3995 LPC1 M.21 M.2 Carrier1 Meters8 Microchip PIC Mircocontroller29 microZed2 microZed Zynq FPGA Carrier2 MIPI CSI5 MIPI DSI4 ModelSim1 MSP430 Launch Pad6 MSP430 Microcontroller10 NVMe1 OCXO3 Oscilloscope2 PCB Test Jig1 PCIe2 PIC32MX3 PIC32MZ4 Programmer5 Qt52 Raspberry PI2 Repair4 Reverse Engineering1 RF5 RF Signal Generator2 Serial Port Programmer2 Smart Sensor3 Solar2 SSD1 Teardown5 Test Instruments11 TMS3202 Tutorial4 Ultrazed2 USB 3.05 USB Interface17 USB Programmer3 USB Video Device Class UVC7 Voltage Reference5 WireFrame5 Wireless2 Xilinx7 Xilinx Zynq Ultrascale+5 Zynq2

Show more Show less

Contact Form

Name

Email *

Message *