tag:blogger.com,1999:blog-4474580574529252327.post9109601645250104942..comments2024-01-31T08:49:41.013+01:00Comments on Embedded Engineering : Simple Kindle E-ink E-paper Display Driver with MSP430 Gaurav Singhhttp://www.blogger.com/profile/17880871396648321687noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-4474580574529252327.post-20809266541093975882018-03-24T16:21:57.076+01:002018-03-24T16:21:57.076+01:00Do you have any problems with ghosting, since the ...Do you have any problems with ghosting, since the eInk display driver doesn't seem to refresh the whole page when using the printstring(.) method. <br />Also another question: The datasheet of the display states, that a whole page refresh takes around 1000ms and consumes 600mW of power typically. Can you confirm these values? <br />Do you have any further documents on the display? I miss a detailed register description for example.<br />I need these information for a university project and any help or information would be very appreciated.Andy Efhttps://www.blogger.com/profile/02809395262302602493noreply@blogger.comtag:blogger.com,1999:blog-4474580574529252327.post-20763222954737873172018-03-23T18:54:49.726+01:002018-03-23T18:54:49.726+01:00there is simlar kohocraft kit (from japan) availab...there is simlar kohocraft kit (from japan) available we had ordered that long back. we also tried with this display to reverse engineer kindle but our singals were not clear like yours our attempts to make it work failed many times and we left that project. but just two days back I took kohocrafts voltage and connector part and ported code to esp32 and it worked. though I could at max use 550x600 resolution buffer.Shirish Jadavhttps://www.blogger.com/profile/02633793772377573992noreply@blogger.comtag:blogger.com,1999:blog-4474580574529252327.post-21731594782348644262017-10-18T22:55:09.494+02:002017-10-18T22:55:09.494+02:00
here is the github repo , everthing is opensource...<br />here is the github repo , everthing is opensource <br /><br />https://github.com/circuitvalley/E-ink_ED060SC4_driver_msp430<br /><br />take a look at schematic for different voltage levels.<br />Gaurav Singhhttps://www.blogger.com/profile/17880871396648321687noreply@blogger.comtag:blogger.com,1999:blog-4474580574529252327.post-72800365465383707442017-10-18T22:31:40.613+02:002017-10-18T22:31:40.613+02:00What Voltages does your driver use?What Voltages does your driver use?Avantyrhttps://www.blogger.com/profile/08487696565408663657noreply@blogger.comtag:blogger.com,1999:blog-4474580574529252327.post-74381497290748720602017-09-03T12:10:22.154+02:002017-09-03T12:10:22.154+02:00Project is written in C source is available in git...Project is written in C source is available in gitrepo , it can not be directly used in arduino IDE, but few changes here and there and it should do the trick.Gaurav Singhhttps://www.blogger.com/profile/17880871396648321687noreply@blogger.comtag:blogger.com,1999:blog-4474580574529252327.post-33868379631625160032017-08-27T04:02:58.103+02:002017-08-27T04:02:58.103+02:00Nice, Project! is it compatible with arduino ?Nice, Project! is it compatible with arduino ?Ferdoushttps://www.blogger.com/profile/14494633294515492834noreply@blogger.com